Kit C50™ Ultimate para Primeiros Socorros
Este kit de máscara de gás inclui:
- Respirador purificador de ar C50™
- Um filtro CTCF50 para agentes antimotim e um filtro CBRNCF50
- Uma cobertura exterior para proteção solar
- Uma cobertura exterior transparente
- Um suporte universal para máscara (ideal para criar um kit de emergência com máscara de gás)
O Governo dos EUA impõe determinados controlos sobre o respirador purificador de ar C50™ e proíbe a exportação, venda, transferência, transporte ou expedição do produto para fora dos EUA sem obter previamente a aprovação do Governo dos EUA ou conforme autorizado pela legislação e regulamentação dos EUA. Esta restrição aplica-se quer o produto se encontre na sua forma original quer tenha sido incorporado noutros artigos. Este produto está sujeito aos Regulamentos de Administração das Exportações (EAR), com a classificação 1A004.
O produto expedido para satisfazer encomendas de comércio eletrónico pode ter mais de um ano.
TENHA EM ATENÇÃO QUE TODAS AS VENDAS SÃO FINAIS. NÃO SERÃO ACEITES DEVOLUÇÕES DE ARTIGOS COM A EMBALAGEM ABERTA.
No caso raro de um produto defeituoso, consulte a nossa política de devoluções e contacte o serviço de apoio ao cliente para obter mais instruções.
Performance
| CBRN Agent Resistance | Requirement | C50 Performance |
|---|---|---|
| Mustard (H) / Sarin (GB) | 36 hours | Greater than 36 hours |
| Soman (GD) / VX | 36 hours | Greater than 36 hours |
| Laboratory protection factor performance (sodium chloride) | 2,000 | Greater than 10,000 |
| Re-breathed CO2 | Less than 1% | 0.8% |
| Inhalation resistance at: | ||
| 30 l/min | 5 mm WG | 3 mm WG |
| 95 l/min | 15 mm WG | 13 mm WG |
| 160 l/min | 25 mm WG | 23 mm WG |
| Exhalation resistance at 160 l/min | 30 mm WG | 15 mm WG |
| Mask weight | N/A | 490 grams |
| NIOSH Visual Field Score (VFS) | 90 | 96 |
Sizing
Please select the correct size according to the sizing chart guide found in the photo gallery for this product.
NOTE: For proper mask fit, faces must be clean shaven.
Facial hair, sideburns, bangs and headwear may prevent a protective facepiece from forming and/or maintaining a tight-fitting seal on someone’s face. It is recommended the user be clean shaven and/or hair pulled back for sizing and using the respirator to ensure an appropriate seal.
To ensure you have selected the correct size you should perform a negative pressure test. The negative pressure test can be performed by putting the mask on your face, breathe out, then block the inhalation valve and take a deep breath. For the FM50 you will need to block both inhalation valves before taking a breath. The mask should collapse to the face. If you experience a tight seal to your face then the mask has the right fit.
If you are still unsure of your size or are certain you are going to be in a hazardous environment and need to ensure the most accurate sizing you may purchase a Sizing Tool.
*Except in the rare case of defective product. Please contact customer service for further instruction in this instance.
Warnings and Limitations of Use
- Always perform a satisfactory negative pressure leak test before using this respirator.
- Do not use in confined spaces such as stills, tanks or sewers. This device does not provide supplied breathable air.
- It is unlikely that the requirements for inward leakage of the system will be met if facial hair, or spectacle side arms pass under the face seal of the full face mask.
- Do not use this equipment in Oxygen deficient atmospheres (<19.5% Oxygen) or for airborne contaminants or pollutants for which the approved filter canister(s) will not provide adequate protection.
- Do not use this equipment in Oxygen enriched atmospheres (> 22.5% Oxygen).
- System set-up, pre-check, donning, doffing, cleaning and maintenance must be performed in an area known to be free of contaminants.
- Do not use if any system component demonstrates signs of wear or damage.
- Do not use in areas where the head harness may be exposed directly to flame.
Potential misuse of the equipment may result in serious, irreversible respiratory harm or death. These actions include:
- Firefighting.
- Modifying, removing or re-configuring any of the system components other than as recommended by the manufacturer.
- Adapting the system to accommodate attachments or apparatus not approved for use by the manufacturer.
- Re-using the equipment without appropriate decontamination or following impact or tear damage without inspection and testing, even though contamination or damage may not be apparent.
- Use with unapproved filter canisters.
